We understand better that enim ad minim veniam, consectetur adipis cing elit, sed do

Steel Roofing Trough · IS 1079 · Punched for 12 mm bolts

SRT Sheet (Steel Roofing Trough) Manufacturer

Mahawar Prefab Solutions (MPS) makes SRT sheets: hot rolled steel to IS 1079, folded into a 613 × 180 mm trough and punched for 12 mm bolts. Lengths from 1270 to 3050 mm in 2.0 or 2.5 mm steel, bare or primed and painted, delivered across India, including Ladakh, Jammu & Kashmir and Punjab.

613 × 180 mm trough2.0 or 2.5 mm steelHoles for 12 mm bolts
SRT sheets (steel roofing troughs) nested in a bundle at the Mahawar Prefab Solutions works
SRTs nested in a bundle at our works
613 × 180 mmwidth × depth of the trough
2.0–2.5 mmhot rolled steel to IS 1079
1270–3050 mmlengths, others made to order
Ø14 mmholes for 12 mm bolts, 36 on a 1700 mm SRT

The basics

What is an SRT sheet?

SRT stands for Steel Roofing Trough. Tenders often write it as “Steel Roofing Through” sheet. It is a hot rolled steel sheet folded on a press into a deep trough: a flat base, two walls 180 mm deep and a flange on each side, 613 mm across in all.

SRTs are used mainly for the roofs of bunkers. They are laid side by side over steel beams, bolted in place through the holes punched in them, and covered with earth. The deep trough shape is what lets a 2 mm sheet carry that load between the beams.

Who we are. MPS is part of Mahawar Group, in the iron and steel trade since 1990. We cut, punch and fold SRTs at our own works, and we also make PEB buildings, C and Z purlins and roofing sheets. See our C and Z purlins.
Three SRT sheets seen from above: flanges and base punched with holes for 12 mm boltsFlange holesBase end holesSRTs punched and folded at our works
A steel sheet punched with bolt holes, ready to be folded into an SRTHoles punched before foldingA punched sheet, ready to fold

In 3D · 360°

Every dimension and every hole, in 3D

Turn the SRT all the way round, 360°, even underneath: drag it with your mouse or finger, or press “360°” and watch it turn. Pick a length, thickness and finish, look at the end profile, the holes at each end and the zig-zag holes along the flanges, and point at any hole to see exactly where it is.

3D model of an SRT sheet 1700 mm long, 613 mm wide and 180 mm deep, with its bolt holes

Sizes and weight

SRT sheet sizes and weight

The trough is the same for every length: 613 mm wide and 180 mm deep. Weights are worked out from the folded shape: 914 mm of steel across, × length × thickness × 7.85.

Overall width613 mmOutside the two flanges.
Depth180 mmFrom the base to the top of the flanges.
Flanges and base175 + 203 + 175 mmThe walls lean out 30 mm so the troughs nest.
Thickness2.0 or 2.5 mmHot rolled carbon steel to IS 1079.
Lengths1270 to 3050 mm1270, 1630, 1700, 2400 and 3050 mm; others to order.
HolesØ14 mmFor 12 mm bolts, punched before folding.
Weight per metre14.35 kgIn 2.0 mm steel (17.92 kg in 2.5 mm).
FinishBare or paintedAs rolled, or red oxide primer and enamel.

Weight of one SRT (kg)

613 × 180 mm trough

Length2.0 mm2.5 mmHoles
1270 mm4.2 ft18.222.832
1630 mm5.3 ft23.429.236
1700 mm5.6 ft24.430.536
2400 mm7.9 ft34.443.040
3050 mm10.0 ft43.854.746

Calculated weights of the bare steel, without paint or bolts. The actual weight varies a little with the steel’s thickness tolerance. If your tender gives a weight per SRT, send it with your list and we will confirm the weight before we cut. Weight of an order = weight of one SRT × number of pieces.

Holes

Where the holes are

All holes are Ø14 mm, for 12 mm bolts, punched while the sheet is still flat. The pattern is the same when the SRT is turned end for end, so it can be laid either way round. Below: a 1700 mm SRT seen from above.

1700 mm401003510535454545103140284284284284284140Flange (175 mm)Base (203 mm)Flange (175 mm)1700 mm401003510535454545103140284284284284284140Flange (175 mm)Base (203 mm)Flange (175 mm)

All holes Ø14 mm, for 12 mm bolts · 36 holes on a 1700 mm SRT · sizes in mm · the darker strips are the two sloping walls, seen from above

Flange end holes2 × 2 in each flange at each end: 40 and 140 mm from the end, 35 mm in from either edge of the flange.
Base end holes2 × 3 in the base at each end: 45, 90, 135 mm from the end, 103 mm apart across the base.
Zig-zag flange holesEvenly spaced between the end groups, alternating between the flange’s two hole lines. On each flange: 2 on a 1270 mm SRT, 4 on 1630 and 1700 mm, 6 on 2400 mm and 9 on 3050 mm.
Bolt kitTenders usually ask for 16 bolts per SRT: 12 × 40 mm, each with a nut and two washers (30 mm across, 3 mm thick). Tell us if you need them.

Applications

Where SRT sheets are used

An SRT roof is built to carry a heavy load of earth and snow on a light steel frame.

Bunker roofsLaid side by side over ISMB steel beams, bolted in place and covered with earth, with a layer of LDPE film in the earth cover. Army works contracts for bunkers specify them.
Bolted, not weldedEvery joint is a 12 mm bolt with a nut and two washers, so the roof goes up with spanners at site: no welding and no cutting.
Made to your tenderSend the item description from your tender or work order: size, thickness, finish and bolts. We make the SRTs to it.

The steel beams and columns that go with them: MS structural steel.

Packing and delivery

Packed to travel to the hills

SRTs are bundled at our works and sent by road to your site, anywhere in India.

Nested bundlesEach SRT sits about 12 mm above the one below, so a bundle of 40 stands only about 649 mm tall and weighs about 980 kg (1700 mm × 2.0 mm).
Painted or bareBare (as rolled) steel rusts in rain and snow. Works contracts often ask for one coat of red oxide primer and two coats of synthetic enamel paint, olive green (OG). We supply either.
The roadThe highways into Ladakh close for several months each winter. For Leh and Kargil, order early in the season so the SRTs reach your site while the roads are open.

Price and ordering

SRT sheet price and how to order

SRT sheets are priced per piece, from the weight of steel in them and the day’s steel rate. Send your list and we will reply with the price and the delivery cost to your site.

  1. Send your list

    On WhatsApp: the size, thickness, quantity and finish, or simply the item description from your tender.

  2. We confirm and quote

    We check the size and holes with you and send the price per SRT and the delivery cost.

  3. Cut, punched and folded

    Your SRTs are made at our works, primed and painted if you asked for it.

  4. Bundled and delivered

    Nested in bundles and sent by road to your site or store.

What to send for a quick quote

  • Size: length × 613 × 180 mm, for example 1700 × 613 × 180
  • Thickness: 2.0 or 2.5 mm
  • Quantity: number of SRTs
  • Finish: bare, primed, or primed and painted (colour)
  • Bolts: if you need the bolt kit with them
  • Delivery location

Building a shed as well? We make PEB buildings, C and Z purlins and colour coated roofing sheets.

FAQ

SRT sheets: questions, answered

Still have a question? Ask us on WhatsApp and our team will answer.

What is the full form of SRT sheet?

SRT stands for Steel Roofing Trough. Tenders often write it as “Steel Roofing Through” sheet. It is a hot rolled steel sheet folded into a deep trough, 613 mm wide and 180 mm deep, with a flange on each side and holes for 12 mm bolts.

What is the size of an SRT sheet?

The trough is 613 mm wide and 180 mm deep: two 175 mm flanges and a 203 mm base. Common lengths are 1270, 1630, 1700, 2400 and 3050 mm, and other lengths are made to order. The usual thickness is 2.0 mm; 2.5 mm is also made.

What is the weight of an SRT sheet?

It depends on the length and thickness. In 2.0 mm steel an SRT weighs about 14.35 kg per metre: about 24.4 kg for a 1700 mm SRT and about 34.4 kg for 2400 mm. A 3050 mm SRT in 2.5 mm steel weighs about 54.7 kg. The weight table on this page lists every size.

Which steel and IS standard is used for SRT?

SRTs are made from hot rolled carbon steel sheet to IS 1079, from leading Indian mills.

How many holes does an SRT have, and for which bolts?

A 1700 mm SRT has 36 holes of Ø14 mm, for 12 mm bolts: 2 × 2 in each flange and 2 × 3 in the base at each end, and 4 zig-zag holes along each flange. Tenders usually ask for 16 bolts per SRT, 12 × 40 mm, each with a nut and two washers.

What is an SRT sheet used for?

Mostly for the roofs of bunkers. SRTs are laid side by side over ISMB steel beams, bolted in place and covered with earth, with a layer of LDPE film in the earth cover.

Are SRT sheets painted?

They can be supplied bare (as rolled), or primed and painted: one coat of red oxide primer and two coats of synthetic enamel paint, olive green (OG), as works contracts often ask.

How are SRT sheets packed and transported?

They nest inside each other: each SRT sits about 12 mm above the one below, so 40 SRTs make a bundle only about 649 mm tall. Bundles go by road to your site.

Do you deliver SRT sheets to Ladakh, Jammu & Kashmir and Punjab?

Yes. We deliver SRT sheets across India, including Ladakh (Leh and Kargil), Jammu & Kashmir and Punjab. For Ladakh, order early in the season: the highways close for several months in winter.

What is the price of SRT sheet?

SRTs are priced per piece, from the weight of steel in them and the day’s steel rate, plus delivery. Send the size, thickness, quantity and finish on WhatsApp for today’s price.

Get a price

Get today’s price for SRT sheets

Send the size, thickness, quantity and finish, or the item from your tender. We will reply with the price per SRT and the delivery cost to your site.

Share and Enjoy !

Shares
Shares